- Manuals
- Brands
- Industrial Electrical
- IntelliRupter PulseCloser
- Instruction sheet
Fault interrupter wi-fi, scada, and gps communication setup
Hide thumbs Also See for IntelliRupter PulseCloser:
- Manual (181 pages) ,
- Installation manual (23 pages) ,
- Quick operating manual (2 pages)
-
- Contents
- Table of Contents
- Troubleshooting
- Bookmarks
Table of Contents
-
Table of Contents
- Table of Contents
- Introduction
-
Qualified Persons
-
Read this Instruction Sheet
-
Retain this Instruction Sheet
-
Proper Application
-
Special Warranty Provisions
-
- Safety Information
-
Following Safety Instructions
-
Replacement Instructions and Labels
- Safety Precautions
- Overview
- Communication Module
-
Maintenance
-
Removing the Communication Module
-
Replacing the Battery
-
Installing a Radio
-
Reinstalling the Communication Module
-
- Wi-Fi Communication Setup
-
Wi-Fi Capability
-
Wi-Fi Antenna
-
- SCADA Communications Setup
-
SCADA Capability
-
DNP Implementation
-
SCADA Antenna
-
SCADA Setup
-
SCADA Diagnostics and Troubleshooting
-
- GPS Communications Setup
-
GPS Capabilities
-
GPS Antenna
-
GPS Setup and Diagnostics
-
Advertisem*nt
Quick Links
Download this manual
IntelliRupter
®
PulseCloser
Outdoor Distribution (15.5 kV, 27 kV, and 38 kV)
Table of Contents
Section
Introduction
Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Read this Instruction Sheet . . . . . . . . . . . . . . . . . . . 2
Retain this Instruction Sheet . . . . . . . . . . . . . . . . . . . 2
Proper Application . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Special Warranty Provisions . . . . . . . . . . . . . . . . . . . 2
Safety Information
Understanding Safety-Alert Messages . . . . . . . . . . . 4
Following Safety Instructions . . . . . . . . . . . . . . . . . . 4
Replacement Instructions and Labels . . . . . . . . . . . 4
Safety Precautions
. . . . . . . . . . . . . . . . . . . . . . . . . 5
Overview
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Communication Module
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Removing the Communication Module . . . . . . . . . . 7
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing a Radio . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Reinstalling the Communication Module . . . . . . . . .13
February 17, 2020
© S&C Electric Company 2008-2020, all rights reserved
®
Fault Interrupter
Wi-Fi, SCADA, and GPS
Communication Setup
Page
Section
Wi-Fi Communication Setup
Wi-Fi Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Wi-Fi Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
SCADA Communications Setup
SCADA Capability . . . . . . . . . . . . . . . . . . . . . . . . . . .15
DNP Implementation . . . . . . . . . . . . . . . . . . . . . . . .15
SCADA Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SCADA Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SCADA Diagnostics and Troubleshooting . . . . . . . .15
GPS Communications Setup
GPS Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
GPS Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
GPS Setup and Diagnostics . . . . . . . . . . . . . . . . . . .16
Instruction Sheet 766-520
Page
Advertisem*nt
Table of Contents
Related Manuals for S&C IntelliRupter PulseCloser
-
Fault interrupter (181 pages)
-
Fault interrupter outdoor distribution (23 pages)
-
Fault interrupter (15 pages)
-
Compact fault interrupter (2 pages)
-
Outdoor distribution (31 pages)
-
Underground distribution switchgear. outdoor distribution with visi-gap load-interrupter switches and visi-gap fault interrupters (27 pages)
-
Pad-mounted gear, outdoor distribution (32 pages)
-
Cutout-mounted recloser outdoor distribution (36 pages)
-
Circuit-switchers-mark vi outdoor transmission (56 pages)
-
Switching system (20 pages)
-
Underground distribution switchgear (27 pages)
-
Cutout-mounted recloser (132 pages)
-
Dropout recloser (24 pages)
-
Cutout-mounted recloser (89 pages)
-
Cutout-mounted recloser (15 pages)
Summary of Contents for S&C IntelliRupter PulseCloser
-
Page 1: Table Of Contents
IntelliRupter ® PulseCloser ® Fault Interrupter Outdoor Distribution (15.5 kV, 27 kV, and 38 kV) Wi-Fi, SCADA, and GPS Communication Setup Table of Contents Section Page Section Page Introduction Wi-Fi Communication Setup Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Wi-Fi Capability . -
Page 2: Introduction
Instruction Sheet Read this instruction sheet thoroughly and carefully before installing or operating your IntelliRupter PulseCloser Fault Interrupter . Familiarize yourself with the Safety Information and Safety Precautions on pages 4 and 5 . The latest version of this publication is available online in PDF format at sandc.com/en/ support/product-literature/ . - Page 3 Introduction Replacement parts provided by the seller or repairs performed by the seller under the warranty for the original equipment will be covered by the above special warranty provision for its duration. Replacement parts purchased separately will be covered by the above special warranty provision.
-
Page 4: Safety Information
Safety Information Understanding Several types of safety-alert messages may appear throughout this instruction sheet and on labels attached to the IntelliRupter PulseCloser Fault Interrupter. Familiarize Safety-Alert Messages yourself with these types of messages and the importance of these various signal words: DANGER “DANGER”... -
Page 5: Safety Precautions
Safety Precautions DANGER IntelliRupter PulseCloser Fault Interrupters operate at high voltage. Failure to observe the precautions below will result in serious personal injury or death. Some of these precautions may differ from your company’s operating procedures and rules . Where a discrepancy exists, follow your company’s operating procedures and rules . -
Page 6: Overview
Overview These instructions cover the Wi-Fi, SCADA, and GPS communication setup of an IntelliRupter PulseCloser Fault Interrupter. The communication module contains a Wi-Fi transceiver, a GPS receiver, and, if specified, a radio providing wide-area network capability in SCADA applications. The communication module may also include... -
Page 7: Communication Module
Communication Module Maintenance The communication module can be easily removed and replaced using a hookstick for maintenance of the battery, Wi-Fi transceiver, GPS receiver, and radio. NOTICE To prevent contamination of the connectors, avoid routine battery replacement during inclement weather, and never place the connector on the ground without some form of protection from dirt and mud . -
Page 8: Replacing The Battery
Communication Module Replacing the Battery Perform the following procedure to replace the battery in the communication module: STEP 1. Loosen the battery compartment cover locking screw using a ⅜ -inch nut driver. See Figure 4. STEP 2. Open the battery compartment cover. See Figure 5. - Page 9 Communication Module STEP 4. Using the fi nger-pull, slide out the existing battery and slide in the replacement battery. See Figure 7. Reconnect the battery leads. STEP 5. Close the battery compartment cover and securely tighten the battery compartment cover locking screw.
-
Page 10: Installing A Radio
Communication Module Installing a Radio A radio providing wide-area network capability for SCADA applications, if specified, is furnished factory-installed in the communication module. Alternately, a user-furnished radio can be installed in the field. Some radios must be programmed using a cable connected to a computer. In such instances, remove the radio tray assembly to connect to the radio, and power the radio with the battery or a separate power supply. - Page 11 Communication Module The radio tray mounting plate, with connections for Wi-Fi/GPS module Wi-Fi/GPS module Battery power, data, and antenna, will be accessible. See Figure 9. Ethernet 2 Ethernet 1 connector STEP 4. Install the radio on the mounting plate using the furnished hardware.
- Page 12 Communication Module STEP 6. Connect the antenna connector to the radio. Ethernet connector Power plug STEP 7. Reinstall the radio tray assembly, and replace and securely tighten the fi ve ¼–20 bolts. Close the battery compartment cover, and tighten the battery compartment cover screw.
-
Page 13: Reinstalling The Communication Module
Communication Module Reinstalling the Communication Module The communication module can be installed from a bucket truck with the module handling fitting, catalog number 4450, attached to a suitable hookstick. CAUTION The communication module is heavy. Removal and replacement from the ground using an extendostick is not recommended . -
Page 14: Wi-Fi Communication Setup
Wi-Fi Communication Setup Wi-Fi Capability The Wi-Fi transceiver in the communication module provides secure wireless point-to-point communication to a wireless-equipped personal computer operating under the IEEE 802.11b standard. Transmission range is typically 150 feet (45.7 meters) or less. The Wi-Fi connection permits local configuration and control of the IntelliRupter fault interrupter. -
Page 15: Scada Communications Setup
SCADA Communication Setup SCADA Capability The IntelliRupter fault interrupter can communicate with a SCADA system via the DNP protocol by using a WAN radio or fiber-optic transceiver installed in the communication module. Alternately, an appropriate SCADA communication device can be housed in a separate pole-mounted enclosure. -
Page 16: Gps Communications Setup
GPS Communication Setup GPS Capabilities A global positioning system (GPS) receiver installed in the communication module provides precise time synchronization. The system allows rapid analysis of event records, simplifying the determination of a sequence of events. GPS Antenna The factory-installed GPS antenna is located on the top of the base as shown in Figure 16.
